Ref. Code
|
Post
|
Educational Qualifications
|
Profile
|
Experience
|
Apply Here
|
| PE1 |
Electrical Engineer
(High Voltage Engineering) |
Graduate In
Electrical
Engineering
|
Experience in design of Engineering of HV & EHV system
with nominal system voltage of 400kV & above. Should be able to lead a team
of engineer engaged in the tasks
listed below.
. To draw up specifications for outdoor high voltage equipment & Gas
insulated switchgear & Commissioning lines and EHV cables.
. To interact with clients & vendors and resolve issues.
. To help generate layout drawings, switching schemes for High Voltage
switchyards.
. To review drawings furnished by vendors
. To make cost estimates for high voltage switch yards & equipment.
. To review quality plan of high voltage equipment
. To inspect & certify test results of high voltage equipment |
8 - 10 years
|
|
| PE2 |
Electrical Engineer
( Power System Studies)
|
Graduate In Electrical Engineering With specialization
in Power Systems High Voltage / Control Systems.
|
Working knowledge of conducting following Power System
Studies at Transmission, Distribution & Plant levels.
. Power Flow studies
. Short circuit studies
. Protection settings & Relay co-ordination
. Transient stability studies
. Harmonic Analysis, Power quality issues and their mitigation
. Insulation co-ordination
. Ability to develop modules to simulate various control systems such as
excitation system governing system etc, using tools like Matlab.
. Earthing system calculations
Hands on experience in conducting the studies using software like ETAP, EDSA,
EMTP would be necessary
|
5 - 10 years.
|
|
| PE3 |
Electrical Engineer
(General Design)
|
Graduate or
Post Graduate In Electrical Engineering
|
Shall have 3 to 8 years experience in Design
calculations for equipment sizing and parameter fixing preparation of
specification, tender analysis and recommendation and vendor drawing reviews of
electrical equipment and systems development of equipment, cable, lighting and
earthing layouts effective interdisciplinary interaction for thermal power
plants and industrial plants.
|
3-8 yrs.
|
|
| PE4 |
Electrical Engineer
(Control and Protection
Specialist)
|
Graduate or
Post Graduate In Electrical Engineering
|
Shall have 10 to 15 years experience in
development of single line diagrams including fixing parameters for equipment,
design of protection schemes from LV to EHV circuits and large turbo
generators, development of logic diagrams and control schemes for switch yards,
HV and MV switch gears and turbogenerators preparation of procurement
specification, bid analysis, vendor drawing approval for control and relay
panels/schemes, MV and HV switch gears, Application engineering with SCADA/DCS
for electrical power supply system, protection settings and Coordination,
Knowledge in latest protection systems of various manufacturers, Good
theoretical knowledge in electrical engineering.
Training young engineers in above activities for large thermal power plants and
industrial plants.
Additionally commissioning or maintenance experience for some duration in above
plants would be considered as added advantage.
|
10-15 yrs.
|
|
| PE5 |
Electrical Engineer
(Control and Protection)
|
Graduate or
Post Graduate In Electrical Engineering
|
Experience in development of single line diagrams
including fixing parameters for equipment design of protection schemes from LV
to EHV circuits ,development of logic diagrams and control schemes for switch
yards, HV and MV switch gears preparation of procurement specification,bid
analysis, vendor drawing approval for control and relay panels/schemes, MV
andHV switch gears.
Application engineering with SCADA/DCS for electrical power supply system
protection settings and coordination, Knowledge in latest protection systems of
various manufacturers, Good theoretical knowledge in electrical engineering for
thermal power plants and industrial plants.
|
5-8yrs.
|
|
| PE6 |
Electrical Engineer
( Project Lead )
|
Graduate or
Post Graduate In Electrical Engineering
|
Experience in development of single line diagrams and
parameter fixing, Basic engineering of all electrical systems preparation of
specification, tender analysis and recommendation and vendor drawing reviews of
electrical equipment and systems development of equipment, cable, lighting and
earthing layouts planning of engineering activities dealing and coordinating
effectively with client and vendors interdisciplinary coordination.
knowledgeable to guide, check outputs from and train juniors for large thermal
power plants and industrial plants.
Additionally inspection, maintenance or commissioning supervision experience
for some duration will be considered as added advantage.
|
8-12yrs.
|
|
| PE7 |
Electrical Engineer
( Sub Station
Engineering)
|
Graduate In Electrical Engineering
|
Experience in Basic and detailed engineering of out
door switch yards and GIS substations up to 400kV, covering evaluation of
switching schemes, design calculations, devising layouts, fixing parameters of
equipment, protection schemes for circuits,SCADA system etc. Preparation of
specification, tender analysis and recommendation and vendor drawing reviews of
switch yard equipment and systems. Familiar with national and international
codes/standards and practices in the design of sub station. Up to date
knowledge on the switch yard equipment/systems. knowledgeable to guide, check
outputs from and train juniors for large power and industrial plants and grid
sub stations. Design engineering knowledge in transmission system will be
considered as added advantage.
|
8-12yrs
|
|
| PE8 |
Electrical Engineer
(Power System
Analysis )
|
Post Graduate In Power System Analysis- Electrical
Engineering
|
Experience in conducting load flow, short circuit,
large motor starting and stability studies and harmonic analysis for large
industrial and utility power systems by using software like ETAP, EDSA etc,
reliability analysis of electrical systems. Good theoretical background for
modeling simulations and problem solving capabilities, relay coordination and
settings. Working knowledge on detailed engineering of electrical systems in
power plants or industrial or chemical plants covering basic engineering,
procurement activities for electrical systems/Equipments for large industrial
plants and utility power systems. Knowledge in basic engineering and detailed
engineering for power plants and large industrial plants will be an added
advantage
|
5-8yrs.
|
|
| PE9 |
Electrical Engineer (Transmission and
Distribution )
|
Graduates in Electrical Engineering;
Masters degree preferred
|
Experience in field of design, procurement, erection,
testing and commissioning of transmission and distribution systems from LT
networks to UHV transmission systems including HVDC systems. Candidates should
be well conversant with National and International Codes and Standards as well
as Statutory and regulatory requirements in the field. Exposure to
international projects is desirable.
. Leading and developing a group of highly dedicated engineers in the field of
Transmission & Distribution Engineering.
. Preparation of Specifications including Bill of Quantities, drawings for
procurement of T&D systems.
. Technical and Commercial analysis of Bids.
. Review of Vendor Drawings.
. Assisting Client in erection, testing and commissioning.
. Trouble shooting.
|
6-10yrs
|
|
| PM1 |
Mechanical Engineer
(Water sytems)
|
Graduate In Mechanical Engineering
|
Experience in Basic and Detailed engineering of water
systems for power projects in leading consulting engineering or EPC contracting
firms or suppliers of water treatment plants / fire protection systems.
Candidates shall have adequate experience in water treatment plants including
RO plants, Cooling water systems (Closed cooling tower based/Once-through
type), fire protection systems for conventional coal based thermal power plants
and gas turbine based combined cycle power plants. Familiarity with applicable
Indian/International codes is amandatory. Exposure to design engineering of
desalination plants would be an added advantage.
. To assist project teams for preparation of feasibility reports / detailed
project reports in regard to water balance diagrams, Sizing criteria/system
description for water systems, cost estimates;
. To carry out basic and detailed engineering of water systems (Water treatment
plants, cooling water systems and fire protection systems) and associated
equipment for all types of power plants; the activities shall include
preparation of design basis reports/basic studies, Preparation of enquiry
specifications, Review of bids, Preparation of technical evaluation reports/
Purchase recommendations, Review and approval of Vendor drawings/documents;
. To carry out detailed engineering of fire protection systems including
hydraulic calculations, fire protection layouts in compliance to TAC/NFPA
guidelines;
. To carry out water audit of existing power plants/industries and suggest
measures for water conservation and effluent treatment;
. To carry out inspection of various equipment like pumps, cooling tower at
shop/site as applicable;
|
4 - 10 years
|
|
| PM2 |
Mechanical Engineer
(Boiler Design)
|
Graduate In Mechanical Engineering /Thermal
Sciences/Engineering is desirable
|
Experience in thermal design of steam generators
(Fluidized bed combustion / pulverized coal fired type) in leading steam
generator manufacturing firm. The candidate shall have sound technical
knowledge on heat transfer, fluid dynamics, two phase flow, metallurgy and
materials and hands-on experience in sizing and disposition of various heat
transfer surfaces viz. furnace, superheater / reheater, evaporator, circulation
checks, performance calculations etc. Familiarity with Indian Boiler
Regulations and other applicable Indian/International codes is a pre-requisite
for this position. Exposure to site activities would be an added advantage.
. To assist project teams in technical evaluation of steam generator and
auxiliaries in respect of review of critical design / performance parameters;
. To assist project teams during detailed engineering phase in respect of
review and approval of engineering documents pertaining to steam generator and
auxiliaries;
. To assist R & M group in carrying out various Renovation &
Modernization related activities for steam generator and auxiliaries;
|
6 - 10 years
|
|
| PM3 |
Mechanical Engineer (Desalination)
|
Graduate In Mechanical Engineering
|
Experience in basic and detailed engineering of
Desalination plants (Membrane based / Thermal desalination) in consulting
engineering or EPC contracting firm or desalination plant suppliers.
Familiarity with applicable Indian/International codes is mandatory.
. To assist project teams in respect of preparation of feasibility reports /
detailed project reports for projects with desalination plants;
. To carry out basic and detailed engineering of desalination plant and
associated systems/equipment for both Membrane based and Thermal desalination
plants; the activities shall include preparation of design basis reports/basic
studies, Preparation of enquiry specifications, Review of bids, Preparation of
technical evaluation reports/Purchase recommendations, Review and approval of
Vendor drawings/documents;
|
4 - 8 years
|
|
| PM4 |
Mechanical Engineer (Biomass Gasification)
|
Graduate In Mechanical Engineering
|
Experience in selection of gasifier technology,
design/sizing of biomass gasifiers, basic and detailed engineering of biomass
gasifier based power projects in consulting engineering or EPC contracting firm
or suppliers of biomass gasifiers.
. To assist project teams for preparation of feasibility reports / detailed
project reports for biomass based power projects in respect of selection of
suitable technology, sizing criteria/system description for various systems,
cost estimates;
. To carry out basic and detailed engineering of biomass gasifier based power
projects; the activities shall include preparation of design basis
reports/basic studies, Preparation of enquiry specifications, Review of bids,
Preparation of technical evaluation reports/Purchase recommendations, Review
and approval of Vendor drawings/documents;
|
4 - 8 years
|
|
| PM5 |
Mechanical Engineer
(Turbo Machinery)
|
Graduate in Mechanical Engineering. Post graduation in
Thermal/Hydro turbo machinery would be desirable.
|
Experience in design engineering of steam/gas
turbines, large capacity air/gas compressors, hydro turbines and associated
sub-systems in leading manufacturing firm. Familiarity with applicable
Indian/International codes is a must.
. To assist project teams with design aspects of turbo-machinery and associated
sub-systems;
. To carry out basic and detailed engineering of power projects with
steam/gas/hydro turbines and/or industrial projects involving drive turbines /
large capacity fuel gas compressors etc; the activities shall include
preparation of design basis reports/basic studies, Preparation of enquiry
specifications, Review of bids, Preparation of technical evaluation reports/
Purchase recommendations, Review and approval of Vendor drawings/documents;
|
4 - 8 years
|
|
| PM6 |
Mechanical Engineer
(Energy Audit /
Demand Side
Management)
|
Graduate in Mechanical/Electrical Engineering with
certification as Energy Managers/Auditors. Post graduation in Energy Management
would be desirable.
|
Experience in carrying out energy audits for power
plants/steel plants/refineries/petro-chemical plants/other power intensive
industries and exposure to demand-side management in power generating
utilities.
. To carry out energy audits for power plants and other major industries;
. To assist project teams in respect of energy conservation measures to be
adopted in new projects/existing plants;
. To assist project teams/clients in respect of demand side management;
|
4 - 8 years
|
|
| PM7 |
Mechanical Engineer-
(Utility Systems)
|
Graduate in Mechanical Engineering
|
Working knowledge of large thermal power plant and
Industrial Plants including:
. Design of utility systems like pumps, fire protection, HVAC, WTP/ETP, cooling
water systems, etc.
. Experience in System Design, Procurement & Post Contract Drawing review.
. Interdisciplinary coordination.
|
2 - 10 years
|
|
| PM8 |
Mechanical Engineer
(Piping)
|
Graduate In Mechanical Engineering
|
Design of piping systems. Knowledge of some of the
aspects of piping like codes and standards, piping materials, concepts of
layouts, static and dynamic stress analysis, 3-D modelling software like PDMS
and PDS is essential. Capable of :
. Generating bill of material
. Piping layouts for steam, water, blast furnace gas
. Planning of supporting systems for the piping layouts
. Procurement of piping, valves & thermal insulation for the power plants
|
2-10 years
|
|
| PM9 |
Mechanical Engineers (Material Handling)
|
Graduate In Mechanical Engineering
|
Design of rotating equipment like pumps, compressors
and material handling equipment etc, with experience in System Design,
Procurement & Post Contract Drawing Review . Capable of :
. Design & Engg and procurement for Coal handling/ash handling systems
. Interface engineering with electrical & civil dept.
. Input/output co-ordination with vendors w.r.t. system requirement.
|
2-10 years.
|
|
| PM10
|
Mechanical Engineer
(Power Plant Processes
and Cycle Equipment)
|
Post Graduate In Mechanical Engineering
|
Process design involving preparation of PFDs, P&I
Ds, layouts, equipment and instrument data sheets etc. Exposure to plant
start-up shall be an added advantage. Capable of :
. Design w.r.t. power plant process and cycle equipment
. Mechanical procurement such as steam generator/ turbine generator &
auxiliary equipment, pumps, compressors etc.
. Co-ordinating with electrical , civil dept and Instrumentation & Control
Dept.
. Experience in System Design, Procurement & Post Contract Drawing Review
required.
|
2-10 years.
|
|
| PC1
|
Civil Engineer
(Dynamic Foundations)
|
Graduate in Civil Engineering. Postgraduate in
Structural Engineering preferred.
|
Design of rigid block foundation for rotary and
reciprocating dynamic equipment.
Design of steam turbine generator and gas turbine generator foundations.
Knowledge of analysis software (ANSYS) will be an added advantage.
|
2 - 10 years
|
|
| PC2
|
Civil Engineer
(Geotechnical)
|
Postgraduate in Geotechnical Engineering
|
. Planning & involving in soil investigation work,
preparation of specification for investigation and foundation works, analysis
of technical & commercial bids, interpretation of soil investigation
reports & foundation recommendation, design of foundation for power plant
& industrial structures.
. Interdisciplinary coordination.
|
2 - 10 years
|
|
| PC3
|
Civil Engineer
(Structures)
|
Postgraduate in Structural Engineering.
|
. Design of foundations, steel and RCC structures,
water retaining structures, pipe racks and sleepers, paving and drainage etc.
in industrial and commercial building projects.
. Interdisciplinary coordination.
|
2 - 10 years
|
|
| PCM
|
Civil/Mechanical Engineer (Contracts Management)
|
Graduate in Civil / Mechanical Engineering
|
. Preparation of contractual documents, bidding
process, negotiations, complete contract documents.
. Knowledgeable in conditioning of contract (Technical, General, financial
& Safetyconditions)
|
10 - 15 years
|
|
| PIC
|
Instrumentation &
Control Engineers
|
Graduate In Instrumentation & Control
|
Experience in Design of instrumentation & control
systems for power projects. Shall be conversant with instrumenting a P&I D,
instrument data sheets, sizing of control valves & safety relief valves,
logic diagrams, interconnection schedules, DCS and PLC etc.
|
2-5 years
|
|
| POM
|
Commissioning Engineers
|
Graduate in Mechanical /Electrical Engineering
|
Experience in start-up, commissioning and/or operation
of large power generation facilities comprising coal-oil-gas fired conventional
plants, combined cycle gas turbine plants and/ or nuclear power plants.
Candidates shall have ability to independently prepare startup procedures &
schedules and pre-commissioning/ commissioning checks.
|
5-10 years
|
|
| POH
|
Operations and Maintenance - Head
|
Graduate in Mechanical Engineering
|
The O&M - Head will be in charge of the company's
O&M business. The applicant shall be graduate engineer of around 50 years
of age, having 15-20 years experience in O&M of thermal power plants. He
shall have worked as Plant Manager/ Plant In-charge in a large power generation
facility (coal / oil / gas fired conventional power plant or combined cycle gas
turbine power plant) or in an O&M organization. The candidate shall have
experience in the operation, maintenance, performance evaluation, maintenance
planning and O&M budgeting. The candidate shall be conversant with all
statutory requirements of running the power plant. Experience in the
preparation of O&M contracts and implementation thereof shall be an added
advantage.
|
15-20 years
|
|
| INSP
|
Inspection Engineer
|
Graduate In Mechanical Engineering
|
EXPERIENCE at Power Plant,Refinery,Valve
manufacturing,Cement/Steel, Chemical
Any process industry with :
Rotary equipment,
Piping
Heat Exchangers
1. Qualified ASNT level 2
. ND testing techniques (Radiographic testing RT)
. Ultrasonic testing
. Magnetic particle Inspection (MPI)
. Liquid Penetrate Inspection
2. Fabrication knowledge
. Level drawing techniques
. Level welding procedure specification preparation
. Level procedural qualification (PQR)
. Level standards ASME Section 1,8
3. Materials knowledge
. Level Standards ASME, ASTM
(Alloy Steel, Casting Steel, Structural Steel)
4. Piping Standards - ASME B 31.1
5. Equipment Inspection
. Pressure vessels
. Rotary equipment
. Valves & fittings
. Piping
|
3-10 years
|
|
| PRM
|
Procurement Engineering
|
Graduate in Mechanical/Electrical Engineering.
Degree/Diploma in Law would be desirable.
|
Experience in in procurement division of large
engineering organisation/EPC Contractor directly dealing with suppliers of
various systems/ equipment for Power/Chemical/ Infrastructure projects. Good
exposure with the current tax regulations in India and experience in handling
international projects/contractors would be desirable.
. To provide a lead role in finalisation of Prequalification requirements, EOI
documents, press notifications for various power projects as applicable.
. Assisting the project teams for finalisation of General Conditions of
Contract for enquiry specification for major contracts.
. Leading the techno-commercial discussions along with the project teams with
bidders in respect of commercial terms and conditions.
. Assisting the purchaser in commercial negotiations as required with
aggressive negotiation skills and by providing latest pricing trends, tax
regulations etc.
. Assisting the project teams in finalisation of Contract documents
. To play a key role in resolving the post-contract clarifications in respect
of commercial terms and conditions.
|
6-10 years
|
|
| PPL
|
Planning Engineer
|
Graduate in Mechanical / Electrical Engineering
|
Project management & coordination activities,
Scheduling & control, Cost control, Coordination with client, vendor &
external agencies, Reporting. Adequate experience in power plant projects
preferable with knowledge of project management tools such as primavera, MS
Project etc. with hands on experience in monitoring and scheduling activities.
|
2-10 years.
|
|
| PCE
|
Engineer- Commercial
|
Graduate in Civil /Electrical / Mechanical Engineering
|
Would be deputed to the Commercial / Business
Development Environment, requiring sound working knowledge of contracts
Management, Negotiation, Proposal Preparation. Preferable experience in
Engineering Consulting (preferably Power Plant Engg).
Effective communication Skills and Willingness to travel, are prerequisites for
consideration.
|
5-10 years
|
|
